Re: The Deadly Device
[Re: ]
#908995
08/20/13 04:59 PM
08/20/13 04:59 PM
|
Joined: Jul 2005
Posts: 23,997 UK
Rushes
True Blue Boomer
|
True Blue Boomer
Joined: Jul 2005
Posts: 23,997
UK
|
Yes, the water should already be in the H20 container. Another member had a similar problem, and MaG said: If you click it on the flask (to measure) it is blue colored - but it is poured. Continue and see. If you still have trouble, perhaps start this part over and double check that all steps up to the point with the water have been done correctly.
"Bleat, Watson -- unmitigated bleat!" ~ Sherlock Holmes
|
|
|
Re: The Deadly Device
[Re: ]
#908996
08/20/13 05:00 PM
08/20/13 05:00 PM
|
Joined: Sep 2015
Posts: 228 Earth
jazzriver
OP
Settled Boomer
|
OP
Settled Boomer
Joined: Sep 2015
Posts: 228
Earth
|
|
|
|
Re: The Deadly Device
[Re: ]
#909171
08/21/13 03:17 PM
08/21/13 03:17 PM
|
Joined: Sep 2015
Posts: 228 Earth
jazzriver
OP
Settled Boomer
|
OP
Settled Boomer
Joined: Sep 2015
Posts: 228
Earth
|
Yes, after I blew up a couple of times. lol.
But now I can't find Ryan. I need to talk to her and she's not in her work space. I don't really know what else to do at this point. The task list says I need to investigate Ryan, explore the lab (which I have done numerous times) and make an etching. I have the cylinder thing but I don't know what to do now. I don't have an image.
I mixed the etching solution and I got the wafer. But I cannot click on the computer. I replaced the conduits. I don't know what else to do.
Last edited by stonzee; 08/21/13 05:27 PM.
|
|
|
Re: The Deadly Device
[Re: ]
#909180
08/21/13 04:00 PM
08/21/13 04:00 PM
|
Joined: Sep 2015
Posts: 228 Earth
jazzriver
OP
Settled Boomer
|
OP
Settled Boomer
Joined: Sep 2015
Posts: 228
Earth
|
Am I supposed to call Deirdre? She's annoying. lol
I gave Ryan the candy bar and that's the last time I saw her. She said she would fix the player. But now she's gone.
Last edited by stonzee; 08/21/13 04:02 PM.
|
|
|
Re: The Deadly Device
[Re: ]
#909184
08/21/13 04:10 PM
08/21/13 04:10 PM
|
Joined: Jul 2000
Posts: 48,421 near Yosemite
Marian
Global Moderator
|
Global Moderator
Sonic Boomer
Joined: Jul 2000
Posts: 48,421
near Yosemite
|
Yes, I think Deirdre was born annoying. It sounds like the next thing you need to do is to make a new circuit board for the small Tesla coil. The next steps, according to the walkthrough, are as follows:
Review how to make a photographic etching: Go down to the lab.
Enter the photolithography lab.
Take the cat leg left of the microscope under the cabinet.
Turn right and read the book on top of the monitor again.
The items needed are: Etching solution, image and blank wafers.
Will this help get you going again?
|
|
|
Re: The Deadly Device
[Re: ]
#909203
08/21/13 06:14 PM
08/21/13 06:14 PM
|
Joined: Jul 2000
Posts: 48,421 near Yosemite
Marian
Global Moderator
|
Global Moderator
Sonic Boomer
Joined: Jul 2000
Posts: 48,421
near Yosemite
|
If you have the etching solution and a silicon wafer, then according to the walkthrough you need to make a circuit design. Look closely at the monitor at the right under the cabinet of the silicon wafers and do the puzzle where you connect all the circuits. When that is done, you can take the circuit design from the printer. Then you can use the photolithography etching machine. Pour the formula in brown bottle on the tank on the left.
Place the printed circuit design on the image tray below the monitor.
Place the silicon wafer on the tray for blank wafers.
Press the red start button. The process will take 12 hours, so you leave and will come back later to this.
|
|
|
|
|